Xaircraft FC1212-P User Manual

XAircraft FC1212-P User Manual V1.03 This Manual is for: FC1212-P and XAircraft Center 1.8

7 / 36 Install Autopilot Autopilot can connect with any port of Port A ~ Port E on FC1212-P through 6 pin cable. Notice: 1. Have to work with Comp

8 / 36 Flash in five seconds High Accuracy GPS Attitude mode, 7 or more Satellites connected. XAircraft Center Overview Installation Get related soft

9 / 36 The Connect button is green when USB Link is connected with PC correctly. FAQ of Connection 1. Error information : connection timeout a) En

10 / 36 XAircraft Center Interface 1. XAircraft Center version and Firmware version. 2. Language option, Chinese and English available. 3. Discon

11 / 36 XAircraft Center User Manual Profile XAircraft Profiles XAircraft official profile list is provided for XAircraft Frames. 1. Using XAircraf

12 / 36 In the Profile Editor, you can input the basic information for your profile. Don’t forget to save your profile after settings changed. Using

13 / 36 Quadcopter（X and + Style） Hexacopter（X, + and Y6） Octacopter (X, + and X8）

14 / 36 Use Other Frames If your frame is not in the wizard, you have to configure the Mixer Table according to the Mixer Rules. Type You can config

15 / 36 Mixer Rules There're only 4 rules to make a mixer settings. 1. Throttle: All the motors should be 100%, servos should be 0. 2. Pitch:

16 / 36 So we got this Mixer Table (using Normal ESCs): Remote Control

Contents DISCLAIMER OF LIABILITY ...

17 / 36 General Input and Calibration 1. Flight Mode (Input 5): flip the Flight Mode switch on transmitter, check the mode shown on software and re

18 / 36 Motor Power On Type 1. Normal: Throttle up to a certain level, the motors start. Throttle down to minimum after 0.5 second, the motor

19 / 36 X.BUS Input Not Released yet. Gimbal Settings Gimbal Remote Control Input Input 9 and Input 10 of FC1212-P are for gimbal, respectively cont

20 / 36 Gimbal Settings Note: FC1212-P does not support multi-circle servos. Multi-circle servo has no end-points. Auto-compensation Settings Angle

21 / 36 In Remote Control, when Input10 signal arrives or exceeds the red neutral line, the shutter servo starts a sequence of half press (focusing)

22 / 36 IMPORTANT: There might be a brake before Position Hold entered in GPS ATT Mode; the brake depends on moving speed of copter.  if spee

23 / 36 Compass Compass Calibration Step 1: Select "Calibrate Compass in the next power on" in AHRS interface of XAircraft Center. Then dis

24 / 36 2. After takeoff, push pitch stick forward, copter fly to east, push roll to right, copter fly to south. 3. Then use yaw stick to make copt

25 / 36 x interval (the interval between two indications) interval () repeat repeat ~ yowl (beeping always) Solid ON For example(buzzer): (.x) means

26 / 36 Firmware Upgrade to start. Step 2: In the prompted firmware list, choose the correct firmware. For example, if you want to upgrade AHRS-S V2

3 / 36 Compass Calibration ...

27 / 36 Step 4: Plug the 4pin cable to AHRS-S V2 as screen shows. If you are upgrading Autopilot, the screen will show an Autopilot in the diagram.

28 / 36 Step 6: Done. Firmware Upgrade FAQ 1. Incorrect Firmware: Check step 2 and step 4, you have to choose proper firmware and plug the 4pin ca

29 / 36 2. Stop at step 4 until it counting down to ZERO. Reason: probably your USB port can’t provide enough power for all devices whic

30 / 36 the propellers before flight to ensure safety. Step 1: Choose Correct Profile Choose correct profile depend on your frame and ESC, the norm

31 / 36 5. Observe whether all propellers spin freely to the right direction. a) If not in the right direction, lower the throttle to minimum and p

32 / 36 Keep turning to one side during flight 1. Check the FC1212-P and Compass install direction. 2. Check the propeller install, to ensure the r

33 / 36 Step 1. Connect the UBEC to the 5th/9th of the power wire. The E3008 has 5 output connectors, and E3009 has 9. Step 2. Connect the UBEC t

34 / 36 Step 3. Use a pincer to pick out all the red wires of 3 pin cable from ESC.

35 / 36 Step 4. Isolate the copper end of the red wire.

36 / 36 Step 5. Connect the ESC to FC as usual.

1 / 36 DISCLAIMER OF LIABILITY 1. Using XAircraft products within the limits permitted by local laws and PLEASE PAY ATTENTION TO THE AGING AND WORN

2 / 36 FC1212-P Interface Note: 1. AUX Function: XAircraft Center software set up for AUX1-3. 2. Output 1-Output 8 Default output is UltraPWM outp

3 / 36 Double flashing in green No valid RC signal detected. Slow Flashing in green FC works normal, ready to fly. Green Light is Solid ON The copter

4 / 36 HITEC，FUTABA，WFLY Receiver Wiring JR，Spektrum Receiver Wiring Other functions: Go to the FC1212-P interface definition for connecting your R

5 / 36 Install AHRS-S V2 and Compass Note： 1. Pay attention the direction of AHRS and Compass when install. 2. Have to use the shock absorption pr

6 / 36 Install AHRS-P AHRS-P has a built-in Compass, compass is susceptible interference by electromagnetism, should avoid electric cables near the